silver christmas tree from paper clips
December 6, 2011 § 7 Comments
Push pins. Rubber bands. And now for my final installment of Christmas décor out of office supplies. A $4 box of 1,000 paper clips made up this avant-garde tree.
I was most looking forward to creating this out of all four trees I made, assuming all four would be equally simple. I was wrong about this one. The concept is simple, but, admittedly, fussy to achieve.
First you have to create a garland of paper clips by stringing them through a thin, light gauge wire. I calculated about 2,000 consecutive seconds (33 minutes, at 2 seconds per paper clip) to finish this first and important step. However, I was also intent on having each paper clip face the exact same way and discovered it was best to string the paper clip through the end that has a smaller loop. The smaller loop acts as a lock to prevent the paper clip from shifting as much as it would had it been strung through the larger loop. And I didn’t account for several spills. Oh, also, 1,000 paper clips weren’t quite sufficient. Luckily, I had some extras stashed from when I designed my paper clip necklace last December. I used about 1,100 paper clips all in all, and the garland took much longer than the time allocated.
Then attaching the garland to a 6″ Styrofoam cone is presumably simple, too. But not. I inserted one end (at least 1-1/2″) of the wire into the side of the cone and started wrapping the garland around the cone (it really is important to use thin wire and not string, as the purpose of the wire is to be stuck into the cone). This was when I ran into the problem of paper clips bunching together. After several ineffective attempts, I managed to keep the paper clips aligned and flat on the table as I slowly wrapped the garland upwards. I made sure I formed the wire along the cone to minimize the garland from sliding down (the weight of 1,100 paper clips will slide down). Again, another important reason to use wire: so that the shape can be maintained. When that is done, then the rest is simple. I just secured the wire (at least 1-1/2″) into the top of the cone.
Despite it all, I’m glad I did this and the other trees! If you’re just tuning in now, over the past three posts I made crystal Christmas trees from push pins, a shag Christmas tree from rubber bands, and rubber-band wrapped trees. Enjoy!
rubber band-wrapped Christmas trees
December 5, 2011 § 11 Comments
I had enough rubber bands to spare from my one-pound bag to make these rubber band-wrapped Christmas trees as the third installment of my Christmas décor from office supplies.
If you’ve missed the previous two, you can find crystal Christmas trees from push pins here and a shag Christmas tree from rubber bands here. And if you’re not into shaggy trees made of rubber bands, these here are chic and just as easy.
Cover Styrofoam cone with rubber bands horizontally. Then vertically. Done! Now wasn’t that quicker than wrapping and gluing cones with sisal?
shag christmas tree from rubber bands
December 5, 2011 § 5 Comments
Now, now. We all know the 70’s have made a feverish comeback. Middle-parted long hair, wide jeans and trousers, and elevator wedges are rapidly ousting teased poufs, skinny pants, and flats. Now onto 70’s shag for some home décor!
As you know, I’ve spent the majority of my weekend making holiday décor out office supplies.
So, I reached for a huge bag of rubber bands at Staples (a pound for less than $4) to hail the big comeback of the 70’s with a quick-n-easy shag Christmas tree. No, not that kind of quick-n-easy shag. Umm. Indeed, a very quirky craft compared to yesterday’s classy crystal Christmas trees from clear push pins. But who doesn’t love quirky?
One pound of rubber bands is more than enough to make two 9″ shag trees.
1. Cut one rubber band open. Thread through rubber bands.
2. When you have enough rubber bands threaded through, tie in a knot to close.
3. Take your ring of rubber bands and place around the bottom of Styrofoam cone.
4. Cut all rubber bands open.
5. Continue steps 1-4 until you have your tree covered.
Now that I’ve stared at this craft for too long, I think I might add paper wings to the sides and a small Styrofoam ball (with closed eyes and a smile) on top of the tree and I’ve got a very unique Christmas angel! I shall try it out…
Another variation of rubber band Christmas trees to follow.
crystal christmas trees from clear push pins
December 4, 2011 § 16 Comments
So this is what my container of push pins got me. Crystal Christmas trees! Ok, not to rival Swarovski. However, an acceptable substitute for those on a dime.
These plastic push pins really shine, far better than I imagined.
One container of 500 push pins (which I picked up at Staples for $6; likely cheaper for lucky Americans with better pricing south of the border!) is enough, with few to spare, to cover one 9″ Styrofoam cone.
Up next (tomorrow), two variations of Christmas trees out of rubber bands…